Divers Tamiseuses à vibrations

 
 

AUTRES GROUPES DE PRODUITS

 
 

Tamiseuse à vibrations

ANALYSETTE 3 SPARTAN

Référence
03.8020.00
Accessoires

La tamiseuse à vibrations ANALYSETTE 3 SPARTAN est livrée en version standard avec le dispositif de verrouillage et le logiciel AUTOSIEVE (disponible 90 jours gratuitement, à l'essai).

Veuillez tenir compte des points suivants : Cette tamiseuse FRITSCH doit être complétée d'un couvercle de tamisage, de tamis d'analyse et d'un fond récepteur.

L'ANALYSETTE 3 est également transformable en un micro-broyeur à vibrations PULVERISETTE 0 afin de fragmenter et d'homogénéiser des échantillons de volume réduit :

FRITSCH PULVERISETTE 0

FRITSCH propose également la tamiseuse ANALYSETTE 3 PRO avec une régulation manuelle d'amplitude :

FRITSCH ANALYSETTE 3 PRO

Accessoires de tamisage à sec

Les tamis d'analyse FRITSCH de diamètre de 100 mm ou 200 mm/8“ dont disponibles avec des couvercles de tamisage en plexiglas, qui permettent d'observer l'opération en cours. Des couvercles de serrage en polyamide sont également disponibles (sans regard) lorsqu'il s'agit de tamiser des matériaux en évitant toute contamination métallique. Nous proposons naturellement aussi les tamis et les fonds récepteurs correspondants, en plastique. Les fonds récepteurs et les fonds récepteurs intermédiaires en acier inoxydable permettant plusieurs tamisages en une opération et ils sont disponibles en toutes les tailles de tamis.

Choisissez les accessoires de tamisage à sec requis

Accessoires de tamisage à sec

clamping lid plexiglas for test sieves 200 mm/8" dia.
N° 31.2020.00
plexiglas for dry sieving with test sieves 200 mm/8" dia.

For dry sieving with test sieves 200 mm/8" dia.


The clamping lid made of plexiglas allows the operator to observe the sieving process.
For applications, where it is not required to observe the sieving process, a clamping lid without window insert article no. 31.2050.00, is also available.
This clamping lid can also be used if you would like to use the Vibratory Micro Mill PULVERISETTE 0 as a Vibratory Sieve Shaker ANALYSETTE 3 SPARTAN. The needed sieve pan and the sieves must be ordered separately.


clamping lid POM plastic (without window) for all test sieves up to 200 mm/8" dia.
N° 31.2050.00
POM plastic - without window - for dry sieving for all test sieves up to 200 mm/8" dia.

For dry sieving for all test sieves up to 200 mm/8" dia.


The POM plastic clamping lid without window for applications, where it is not required to observe the sieving process, respectively in order to sieve materials where a metallic contamination must be avoided. For applications, where it is required to observe the sieving process, a clamping lid with window insert article no. 31.2020.00, is also available.
This clamping lid can also be used if you would like to use the Vibratory Micro Mill PULVERISETTE 0 as a Vibratory Sieve Shaker ANALYSETTE 3 SPARTAN.
The needed sieve pan and the sieves must be ordered separately.


ANALYSE DE RÉFÉRENCE
General specifications
MaterialPOM Polyoxymethylene
ISO/EN/DIN CodeDIN 7728 C9021
Chemical composition
ElementFormula
Polyoxmethylenecopolymer (Polyacetale)CxH2xOx
Melting point165° C
max. Application temp. constant90°
max. Application temp. briefly140°
Chemical Resistance
Aliphatical hydrocarbon
Aromatical hydrocarbon
Halogenised hydrocarbon
weak acid
strong alkaline solution
Physical and mechanical properties
Density141,g /cm³
Hardnessextremely hard
sieve tensioning system TorqueMaster incl. clamping lid plexiglas for test sieves 200 mm/8" dia. and electrical tool
N° 31.2100.00
Sieve Tensioning System TorqueMaster incl. clamping lid plexiglas and electrical tool 100-240 V/1~, 50-60 Hz

For dry sieving with test sieves 200 mm/8" dia.

Consisting of clamping lid plexiglas for test sieves 200 mm and 8" dia. and electrical tool 100 -240 V/1~, 50 -60  Hz

TorqueMaster enables automatic and reproducible tensioning of the sieve stack on the sieve shaker during dry sieving with test sieves 200 mm/8" diameter. Although the tensioning has a great influence on the sieving result, it is relatively undefined in conventional systems. The universal sieve clamping system TorqueMaster delivers constant and reproducible clamping forces of ~ 1 kN to the sieve stack, enabling the calibration of the sieve tensioning – essential when using the ANALYSETTE 3 PRO as inspection instrument according to ISO 9001.

Although you may not have a FRITSCH sieve shaker, the TorqueMaster is the best tensioning system for your sieve stack. TorqueMaster can be attached and used with any sieve shaker.


clamping lid POM plastic for test sieves 100 mm dia.
N° 31.2016.00
clamping lid POM plastic with security glass for test sieves 100 mm dia.

Clamping lid POM plastic with security glass for dry sieving with test sieves 100 mm dia. and grinding head for conversion of the ANALYSETTE 3 to the PULVERISETTE 0.
The clamping lid with security glass allows the operator to observe the sieving process and the ANALYSETTE 3 can be used with this clamping lid as Vibratory Micro Mill PULVERISETTE 0 for milling and homogenizing of small quantities of samples (sample quantity: 0.1 – 10 ml, max. feed size: < 5 mm, final fineness: 5 – 10 µm).


ANALYSE DE RÉFÉRENCE
General specifications
MaterialPOM Polyoxymethylene
ISO/EN/DIN CodeDIN 7728 C9021
Chemical composition
ElementFormula
Polyoxmethylenecopolymer (Polyacetale)CxH2xOx
Melting point165° C
max. Application temp. constant90°
max. Application temp. briefly140°
Chemical Resistance
Aliphatical hydrocarbon
Aromatical hydrocarbon
Halogenised hydrocarbon
weak acid
strong alkaline solution
Physical and mechanical properties
Density141,g /cm³
Hardnessextremely hard
interposed sieve pan made of stainless steel 200 mm dia., 50 mm height
N° 31.1300.03
Interposed sieve pan made of stainless steel 200 mm dia., 50 mm height

For dry sieving with test sieves 200 mm dia.

If several sieving operations should be carried out simultaneously, an interposed sieve pan must be used as sieve pan between the sieves.


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
interposed sieve pan made of stainless steel 8" dia., 2" height
N° 31.1320.03
Interposed sieve pan made of stainless steel 8" dia., 2" height

For dry sieving with test sieves 8" dia.

If several sieving operations should be carried out simultaneously, an interposed sieve pan must be used as sieve pan between the sieves.


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
sieve pan made of stainless steel 200 mm dia., 50 mm height
N° 31.1000.03
Sieve pan made of stainless steel 200 mm dia., 50 mm height

For dry sieving with test sieves 200 mm dia.

The sieve pan made of stainless steel completes the sieve stack.


 


The sieve pan made of stainless steel is also available in 200 mm dia., 25 mm height.


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
sieve pan made of stainless steel 8" dia., 2" height
N° 31.1020.03
Sieve pan made of stainless steel 8" dia., 2" height

For dry sieving with test sieves 8" dia.

The sieve pan made of stainless steel completes the sieve stack.


 


This sieve pan made of stainless steel is also available in 8" dia., 1" height.


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
sieve pan made of stainless steel 100 mm dia., 40 mm height
N° 31.1040.03
Sieve pan made of stainless steel 100 mm dia., 40 mm height

For dry sieving with test sieves 100 mm dia.

The sieve pan made of stainless steel completes the sieve stack.


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data

Accessoires de tamisage par voie humide

Lors d'un tamisage par voie humide avec des tamis d'analyse (200 mm/8“), le couvercle de tamisage assure un arrosage régulier de l'échantillon, via 2 buses rotatives, afin d'obtenir le meilleur tamisage possible. Des tamis annulaires intermédiaires à trois buses sont spécialement conçus pour pulvériser simultanément le tamis supérieur et le tamis inférieur. Un couvercle de tamisage en plexiglas à 1 buse est disponible pour le tamisage par voie humide à tamis d'analyse de 100 mm. Les fonds récepteurs à goulotte d'évacuation correspondant à toutes les tailles de tamis sont disponibles.

Choisissez les accessoires de tamisage par voie humide

Accessoires de tamisage par voie humide

clamping lid plexiglas with 2 rotation nozzles for test sieves 200 mm/8" dia.
N° 31.0400.00
plexiglas for wet sieving with test sieves 200 mm/8" dia

With 2 rotation nozzles for wet sieving with test sieves 200 mm/8" dia.

The wet clamping lid features 2 rotation nozzles which sprays the entire interior chamber, thus helping to flush the material through the sieve apertures.
Especially recommended for materials with a high electrostatic charge or very high content of fine material. This clamping lid can also be used if you would like to use the Vibratory Micro Mill PULVERISETTE 0 as a Vibratory Sieve Shaker ANALYSETTE 3 SPARTAN. The needed sieve pan and the sieves must be ordered separately.


sieve pan made of stainless steel with outlet 200 mm dia., 50 mm height
N° 31.1100.03
Sieve pan made of stainless steel with outlet 200 mm dia., 50 mm height

For wet sieving with test sieves 200 mm dia.

The sieve pan made of stainless steel with outlet completes the sieve stack.


This sieve pan made of stainless steel with outlet is also available in 200 mm dia., 25 mm height.


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
interposed sieving ring with 3 nozzles for test sieves 200 mm dia.
N° 31.0240.00
Interposed sieving ring with 3 nozzles

For wet sieving with test sieves 200 mm dia.

For simultaneous spraying the sieves above and below.


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
Venting ring for test sieves 200 mm dia.
N° 31.1330.03
Venting ring for test sieves

Venting ring for test sieves 200 mm dia. - required when utilizing test sieves < 100 µm. Venting rings are used to prevent the occurrence of air cushions during wet sieving.


sieve pan made of stainless steel with outlet 8" dia., 2" height
N° 31.1120.03
Sieve pan made of stainless steel with outlet 8" dia., 2" height

For wet sieving with test sieves 8" dia.

The sieve pan made of stainless steel with outlet completes the sieve stack.


This sieve pan made of stainless steel with outlet is also available in 8" dia., 1" height.


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
interposed sieving ring with 3 nozzles for test sieves 8" dia.
N° 31.0250.00
Interposed sieving ring with 3 nozzles

For wet sieving with test sieves 8" dia.

For simultaneous spraying the sieves above and below.


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
Venting ring for test sieves 8" dia.
N° 31.1340.03
Venting ring for test sieves

Venting ring for test sieves 8" dia. - required when utilizing test sieves < 100 µm. Venting rings are used to prevent the occurrence of air cushions during wet sieving.


clamping lid plexiglas with 1 nozzle for test sieves 100 mm dia.
N° 31.2040.00
Clamping lid plexiglas

with 1 nozzles for wet sieving with test sieves 100 mm dia.

The wet clamping lid features 1 nozzle which sprays the entire interior chamber, thus helping to flush the material through the sieve apertures.

Especially recommended for materials with a high electrostatic charge or very high content of fine material. 


This clamping lid can also be used if you would like to use the Vibratory Micro Mill PULVERISETTE 0 as a Vibratory Sieve Shaker ANALYSETTE 3 SPARTAN. The needed sieve pan and sieves must be ordered separately.


sieve pan made of stainless steel with outlet 100 mm dia., 40 mm height
N° 31.1140.00
Sieve pan made of stainless steel with outlet 100 mm dia., 40 mm height

For wet sieving with test sieves 100 mm dia.

The sieve pan made of stainless steel with outlet completes the sieve stack.


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data

Certification

Documentation IQ/OQ pour l'ANALYSETTE 3 SPARTAN et certificat de réception 3.1 EN 10204.

Choisissez la certification

Certification

IQ/OQ documentation for FRITSCH Sieve Shaker ANALYSETTE 3 SPARTAN
N° 96.0100.00
IQ/OQ documentation for FRITSCH Sieve Shaker ANALYSETTE 3 SPARTAN

IQ/OQ documentation (questionnaire format - implementation by customer) for the independent utilization for the support of instrument qualification in the quality management system for the Vibratory Sieve Shaker ANALYSETTE 3 SPARTAN.


Inspection certificate 3.1 EN 10204 for FRITSCH test sieves according to ISO 3310-1
N° 31.0900.00
Inspection certificate 3.1 EN 10204 for FRITSCH test sieves according to ISO 3310-1

Inspection certificate 3.1 EN 10204 for test sieves according to ISO 3310-1


The inspection certificate 3.1 EN 10204 is essential when using the test sieves as testing equipment in accordance with DIN EN ISO 9001.


Of course, we would also be happy to recertify your FRITSCH test sieves according to ISO 3310-1 at our headquarters in Idar-Oberstein.


Please note: if necessary please order together with each test sieve.


Accessoires d'analyse de tamisage

Un formulaire destiné à la documentation IQ/OQ et un certificat de réception 3.1 EN 10204 attestent que l'instrument ANALYSETTE 3 PRO est un instrument de contrôle. Un certificat de réception 3.1 EN 10204 est également disponible pour les tamis d'analyse FRITSCH, selon ISO 3310 -1.

Choisissez les accessoires d'analyse automatique du tamisage

Accessoires d'analyse de tamisage

Software AUTOSIEVE-activation
N° 03.2902.00
Software AUTOSIEVE for Windows for control and automatic evaluation of sieve analysis (price for software activation)

Software AUTOSIEVE-activation for installation on up to 3 Windows PC's after expiration of the free of charge test phase for FRITSCH software AUTOSIEVE for Windows.


System requirements - Software AUTOSIEVE
Minimum software requirements: Windows 7 or higher
Minimum hardware requirements: standard WINDOWS ™ PC with at least 2 Gbyte RAM


Your advantages with AUTOSIEVE:

  • Automatic evaluation of your sieve Analysis
  • Simple monitoring and documentation of your sieving results
  • Suitable for all FRITSCH Sieve Shakers: Vibratory Sieve Shakers ANALYSETTE 3 PRO and ANALYSETTE 3 SPARTAN and the Heavy Duty Analytical Sieve Shaker ANALYSETTE 18
  • After conducting your sieving– simply connect the laboratory analysis balance, then weigh the sieves before and after sieving using differential weighing – AUTOSIEVE will do the rest
  • Extensive presentation of the results: presentation and printout as cumulative or frequency distribution and as graphs according to DIN ISO 9276-1
  • Controlling of the Vibratory Sieve Shaker ANALYSETTE 3 PRO and entry of all functions such as amplitude, sieving time, interval operation and the type of sieving comfortable via the computer
  • Monitoring of the sieving via the online-comparison of the set and actual amplitude and therefore an auto validation of the sieving process with the Vibratory Sieve Shaker ANALYSETTE 3 PRO

FRITSCH offers for the differential weighing of the sieves a special laboratory analysis balance for the Vibratory Sieve Shakers ANALYSETTE 3 PRO and SPARTAN, which you can order with the following order no. 03.2600.00.
A laboratory analysis balance for the Heavy Duty Analytical Sieve Shaker ANALYSETTE 18 is available on request.


laboratory analysis balance
N° 03.2600.00
Laboratory analysis balance

Up to 4.1 kg (± 0.01 g) with RS232 interface, incl. computer connection cable for automatic sieve evaluation.


The extensive Software AUTOSIEVE for WindowsTM enables the automatic sieve evaluation with every FRITSCH Sieve Shaker. For this purpose a special laboratory analysis balance is required for the Vibratory Sieve Shakers ANALYSETTE 3 PRO and SPARTAN, which you can order with the above mentioned order no. 03.2600.00.


A laboratory analysis balance for the Heavy Duty Analytical Sieve Shaker ANALYSETTE 18 is available on request.


Accessoires de tamisage

Nous proposons de nombreux accessoires de tamisage, à l'instar des auxiliaires de tamisages, des couvercles, des joints de rechange et concentré de nettoyage pour tamis.
Pour le tamisage à sec de matériaux à fraction fine importante, utiliser comme auxiliaire de tamisage des billes d'agate de 10 mm ou des billes de caoutchouc de 20 mm lorsque le tamis est moyen ou gros et des billes d'agate de 5 mm lorsque le tamis est fin. L'avantage pour vous : vous empêchez tout colmatage de la toile de tamisage. 

Choisissez les accessoires de tamisage

Auxiliaires de tamisage

agate - SiO2 - polished
N° 55.0050.05
Grinding ball agate, 5 mm dia., polished

General material specification:
Material: agate - SiO2
Abrasion resistance: good
Suitable for: soft to medium-hard sample
100 grinding balls made of agate with 5 mm dia. weigh approx. 17 g. With the weight information, the high number of balls per grinding bowl can be determined by weighing.
Grinding balls made of agate with 5 mm dia. are also recommended as sieving aid for dry sieving of material with a high proportion of fine particles.
Recommended number per sieve: 15 pieces.


ANALYSE DE RÉFÉRENCE
General specifications
MaterialAgate – SiO2
Chemical composition
ElementShare %
Silicon oxide– SiO299.9
Aluminium – Al2O3< 0.02
Iron oxide – Fe2O3< 0.02
Calcium oxide – CaO< 0.02
Magnesium oxide – MgO< 0.02
Sodium oxide – Na2O< 0.02
Potassium oxide – K2O< 0.02
Manganese oxide – MnO< 0.02
Physical and mechanical properties
Density2.65 g/cm³
Hardness6.5 – 7 Mohs


Explanations on hardness data
agate - SiO2 - polished
N° 55.0100.05
Grinding ball agate 10 mm dia., polished

General material specification:
Material: agate - SiO2
Abrasion resistance: good
Suitable for: soft to medium-hard sample
Grinding balls made of agate with 10 mm dia. are also recommended as sieving aid for dry sieving of material with a high proportion of fine particles.
Recommended number per sieve: 10 pieces.


ANALYSE DE RÉFÉRENCE
General specifications
MaterialAgate – SiO2
Chemical composition
ElementShare %
Silicon oxide– SiO299.9
Aluminium – Al2O3< 0.02
Iron oxide – Fe2O3< 0.02
Calcium oxide – CaO< 0.02
Magnesium oxide – MgO< 0.02
Sodium oxide – Na2O< 0.02
Potassium oxide – K2O< 0.02
Manganese oxide – MnO< 0.02
Physical and mechanical properties
Density2.65 g/cm³
Hardness6.5 – 7 Mohs


Explanations on hardness data
rubber ball 20 mm dia.
N° 31.0180.15
Rubber ball 20 mm dia.

Are recommended as sieving aids for dry sieving of materials with a high proportion of fine particles.

Recommended quantity per sieve: 5 pieces


Couvercle de tamis

for test sieves 200 mm dia.
N° 31.1200.03
Sieve cover made of stainless steel for test sieves 200 mm dia.

Sieve cover for a test sieve 200 mm dia. or to cover the whole sieve stack 200 mm dia.


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
for test sieves 8" dia.
N° 31.1220.03
Sieve cover made of stainless steel for test sieves 8" dia.

Sieve cover for a test sieve 8" dia. or to cover the whole sieve stack 8" dia.


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
for test sieves 100 mm dia.
N° 31.1240.03
Sieve cover made of stainless steel for test sieves 100 mm dia.

Sieve cover for a test sieve 100 mm dia. or to cover the whole sieve stack 100 mm dia.


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4404/316L
ISO/EN/DIN codeX2CrNiMo17-12-2
Chemical composition
ElementShare %
Iron – Feapprox. 62.8
Carbon – C0.03
Silicon – Si1
Manganese – Mn2
Phosphorus – P0.045
Sulphur – S0.015
Chromium – Cr18.5
Molybdenum – Mo2.50
Nickel – Ni13.00
Nitrogen – N0.110
Physical and mechanical properties
Density8.0 g/cm³
Hardness215 HB



Explanations on hardness data

Joints d'étanchéité

for test sieves 200 mm/8" dia., 50 mm/2" height, 200 mm dia., 25 mm height
N° 31.0010.16
Replacement seal ring NBR

Replacement seal ring NBR for test sieves:


200 mm dia., 50 mm height


8" dia., 2" height


200 mm dia., 25 mm height


Replacement seal ring NBR for test sieves 100 mm dia.
N° 31.0520.16
Replacement seal ring NBR for test sieves 100 mm dia.

Replacement seal ring NBR for test sieves:


100 mm dia.


Concentré de nettoyage pour tamis

concentrated cleaning liquid, can of 2.5 litres
N° 17.0400.00
Concentrated cleaning liquid, can of 2.5 litres

Can of 2.5 litres concentrated cleaning liquid, alkaline, for dilution 1:33.


Ideal for gentle and effective cleaning of your test and micro-precision sieves. With reliable protection
against corrosion of stainless steel, nickel and bronze.


ANALYSE DE RÉFÉRENCE
General specifications
Chemical formulaCombination of tensides, glycols and environmentally friendly complexing agents
RegulationsNot subject to labelling requirements according to the EC-Guidelines for Hazardous Materials Ordinance
Density~ 1.01 g/cm3
PH value> 11 (undiluted)
Toxicological informationnon-irritant for skin, eyes etc.
First aidrefer to enclosed label
Environmental informationdo not discard into groundwater, canalisation or bodies of water
DisposalMust be according to official regulations be specially treated prior to discarding

Accessoires pour le broyage et l’homogénéisation de petites quantités

clamping lid POM plastic for test sieves 100 mm dia.
N° 31.2016.00
clamping lid POM plastic with security glass for test sieves 100 mm dia.

Clamping lid POM plastic with security glass for dry sieving with test sieves 100 mm dia. and grinding head for conversion of the ANALYSETTE 3 to the PULVERISETTE 0.
The clamping lid with security glass allows the operator to observe the sieving process and the ANALYSETTE 3 can be used with this clamping lid as Vibratory Micro Mill PULVERISETTE 0 for milling and homogenizing of small quantities of samples (sample quantity: 0.1 – 10 ml, max. feed size: < 5 mm, final fineness: 5 – 10 µm).


ANALYSE DE RÉFÉRENCE
General specifications
MaterialPOM Polyoxymethylene
ISO/EN/DIN CodeDIN 7728 C9021
Chemical composition
ElementFormula
Polyoxmethylenecopolymer (Polyacetale)CxH2xOx
Melting point165° C
max. Application temp. constant90°
max. Application temp. briefly140°
Chemical Resistance
Aliphatical hydrocarbon
Aromatical hydrocarbon
Halogenised hydrocarbon
weak acid
strong alkaline solution
Physical and mechanical properties
Density141,g /cm³
Hardnessextremely hard

Tamis d'analyse en acier inoxydable, 200 mm Ø, 50 mm de haut selon ISO 3310-1

Aide à la sélection
 
  • Si vous souhaitez un tamis d'analyse de dimensions différentes, tenez compte des exemples de commande mentionnés :

    Écart par rapport aux tailles standard de tamis ISO 3310-1 ouverture de mailles mm/µm ASTM E11 mesh
    Tamis d'analyse à ouverture de mailles de 5 mm
    Ø 200 mm, hauteur 50 mm = taille standard
    par exemple 30.1800.03 par exemple 35.1800.03
    Tamis d'analyse à ouverture de mailles de 5 mm
    Ø 200 mm, hauteur 25 mm
    dans la référence de commande, remplacer le 0 par un 1, à la cinquième position par exemple 30.1810.03 par exemple 35.1810.03
    Tamis d'analyse à ouverture de mailles de 5 mm
    Ø 8", hauteur 2"
    dans la référence de commande, remplacer le 0 par un 2, à la cinquième position par exemple 30.1820.03 par exemple 35.1820.03
    Tamis d'analyse à ouverture de mailles de 5 mm
    Ø 100 mm, hauteur 40 mm
    dans la référence de commande, remplacer le 0 par un 4, à la cinquième position par exemple 30.1840.03 par exemple 35.1840.03
  • Autres informations

    Des tamis d'analyse et accessoires de tamisage d'autres diamètres et ouvertures de maille sont disponibles sur demande.
    Des tamis d'analyse en polyamide sont disponibles sur demande.
    Aucun tamis d'analyse et accessoires de tamis ne peut être échangé.

Pour le tamisage à sec et par voie humide, ouverture de maille comprise entre 20 μm et 63 mm : particulièrement léger et robuste, fabrication haut de gamme. L'acier inoxydable fortement allié protège de la corrosion et facilite le nettoyage. Les jonctions sans rainure de la toile empêchent la souillure du produit à tamiser. Tous les tamis sont gravés au laser, mesurés avec un système optique et fournis avec un certificat d'usine.

Choisissez les tamis d'analyse

Tamis d'analyse en acier inoxydable, 200 mm Ø, 50 mm de haut selon ISO 3310-1, avec certificat d'usine

63 mm mesh width
N° 30.0000.03
Test sieve, mesh width 63 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
45 mm mesh width
N° 30.0005.03
Test sieve, mesh width 45 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
31.5 mm mesh width
N° 30.0100.03
Test sieve, mesh width 31.5 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
25 mm mesh width
N° 30.0200.03
Test sieve, mesh width 25 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
22.4 mm mesh width
N° 30.0300.03
Test sieve, mesh width 22.4 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
20 mm mesh width
N° 30.0400.03
Test sieve, mesh width 20 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
19 mm mesh width
N° 30.0500.03
Test sieve, mesh width 400 µm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
18 mm mesh width
N° 30.0600.03
Test sieve, mesh width 18 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
16 mm mesh width
N° 30.0800.03
Test sieve, mesh width 16 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
14 mm mesh width
N° 30.0900.03
Test sieve, mesh width 14 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
12.5 mm mesh width
N° 30.1000.03
Test sieve, mesh width 12.5 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
11.2 mm mesh width
N° 30.1100.03
Test sieve, mesh width 11.2 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
10 mm mesh width
N° 30.1200.03
Test sieve, mesh width 10 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
9 mm mesh width
N° 30.1300.03
Test sieve, mesh width 9 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
8 mm mesh width
N° 30.1400.03
Test sieve, mesh width 8 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
7.1 mm mesh width
N° 30.1500.03
Test sieve, mesh width 7.1 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
6.3 mm mesh width
N° 30.1600.03
Test sieve, mesh width 6.3 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
5.6 mm mesh width
N° 30.1700.03
Test sieve, mesh width 5.6 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
5 mm mesh width
N° 30.1800.03
Test sieve, mesh width 5 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
4.5 mm mesh width
N° 30.1900.03
Test sieve, mesh width 4.5 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
4 mm mesh width
N° 30.2000.03
Test sieve, mesh width 4 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
3.55 mm mesh width
N° 30.2100.03
Test sieve, mesh width 3.55 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
3.15 mm mesh width
N° 30.2200.03
Test sieve, mesh width 3.15 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
2.8 mm mesh width
N° 30.2300.03
Test sieve, mesh width 2.8 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
2.5 mm mesh width
N° 30.2400.03
Test sieve, mesh width 2.5 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
2.24 mm mesh width
N° 30.2500.03
Test sieve, mesh width 2.24 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
2 mm mesh width
N° 30.2600.03
Test sieve, mesh width 2 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
1.8 mm mesh width
N° 30.2700.03
Test sieve, mesh width 1.8 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
1.6 mm mesh width
N° 30.2800.03
Test sieve, mesh width 1.6 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
1.4 mm mesh width
N° 30.2900.03
Test sieve, mesh width 1.4 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
1.25 mm mesh width
N° 30.3000.03
Test sieve, mesh width 1.25 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
1.12 mm mesh width
N° 30.3100.03
Test sieve, mesh width 1.12 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
1 mm mesh width
N° 30.3200.03
Test sieve, mesh width 1 mm, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
900 µm mesh width
N° 30.3300.03
Test sieve, mesh width 900 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
850 µm mesh width
N° 30.3305.03
Test sieve, mesh width 850 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
800 µm mesh width
N° 30.3400.03
Test sieve, mesh width 800 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
710 µm mesh width
N° 30.3500.03
Test sieve, mesh width 710 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
630 µm mesh width
N° 30.3600.03
Test sieve, mesh width 630 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
600 µm mesh width
N° 30.3605.03
Test sieve, mesh width 600 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
560 µm mesh width
N° 30.3700.03
Test sieve, mesh width 560 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
500 µm mesh width
N° 30.3800.03
Test sieve, mesh width 500 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
450 µm mesh width
N° 30.3900.03
Test sieve, mesh width 450 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
400 µm mesh width
N° 30.4000.03
Test sieve, mesh width 400 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
355 µm mesh width
N° 30.4100.03
Test sieve, mesh width 355 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
315 µm mesh width
N° 30.4200.03
Test sieve, mesh width 315 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
300 µm mesh width
N° 30.4205.03
Test sieve, mesh width 300 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
280 µm mesh width
N° 30.4300.03
Test sieve, mesh width 280 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
250 µm mesh width
N° 30.4400.03
Test sieve, mesh width 250 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
224 µm mesh width
N° 30.4500.03
Test sieve, mesh width 224 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
212 µm mesh width
N° 30.4505.03
Test sieve, mesh width 212 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
200 µm mesh width
N° 30.4600.03
Test sieve, mesh width 200 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
180 µm mesh width
N° 30.4700.03
Test sieve, mesh width 180 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
160 µm mesh width
N° 30.4800.03
Test sieve, mesh width 160 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
150 µm mesh width
N° 30.4805.03
Test sieve, mesh width 150 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
140 µm mesh width
N° 30.4900.03
Test sieve, mesh width 140 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
125 µm mesh width
N° 30.5000.03
Test sieve, mesh width 125 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
112 µm mesh width
N° 30.5100.03
Test sieve, mesh width 112 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
106 µm mesh width
N° 30.5105.03
Test sieve, mesh width 106 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
100 µm mesh width
N° 30.5200.03
Test sieve, mesh width 100 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
90 µm mesh width
N° 30.5400.03
Test sieve, mesh width 90 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
80 µm mesh width
N° 30.5600.03
Test sieve, mesh width 80 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
75 µm mesh width
N° 30.5700.03
Test sieve, mesh width 75 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
71 µm mesh width
N° 30.5800.03
Test sieve, mesh width 71 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
63 µm mesh width
N° 30.6000.03
Test sieve, mesh width 63 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
56 µm mesh width
N° 30.6200.03
Test sieve, mesh width 56 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
53 µm mesh width
N° 30.6300.03
Test sieve, mesh width 53 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
50 µm mesh width
N° 30.6400.03
Test sieve, mesh width 50 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
45 µm mesh width
N° 30.6600.03
Test sieve, mesh width 45 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
40 µm mesh width
N° 30.6800.03
Test sieve, mesh width 40 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
38 µm mesh width
N° 30.6900.03
Test sieve, mesh width 38 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
36 µm mesh width
N° 30.7000.03
Test sieve, mesh width 36 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
32 µm mesh width
N° 30.7200.03
Test sieve, mesh width 32 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
25 µm mesh width
N° 30.7600.03
Test sieve, mesh width 25 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
20 µm mesh width
N° 30.7800.03
Test sieve, mesh width 20 <span class="to-lower">µm</span>, ISO 3310-1

Test sieve 200 mm dia., 50 mm height, frame and mesh wire made of stainless steel with compliance certificate.
In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
8" dia., 2" height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data

8" intérieur, 2" de hauteur, selon ASTM E11 mesh

Aide à la sélection
 
  • Si vous souhaitez un tamis d'analyse de dimensions différentes, tenez compte des exemples de commande mentionnés :

    Écart par rapport aux tailles standard de tamis ISO 3310-1 ouverture de mailles mm/µm ASTM E11 mesh
    Tamis d'analyse à ouverture de mailles de 5 mm
    Ø 200 mm, hauteur 50 mm = taille standard
    par exemple 30.1800.03 par exemple 35.1800.03
    Tamis d'analyse à ouverture de mailles de 5 mm
    Ø 200 mm, hauteur 25 mm
    dans la référence de commande, remplacer le 0 par un 1, à la cinquième position par exemple 30.1810.03 par exemple 35.1810.03
    Tamis d'analyse à ouverture de mailles de 5 mm
    Ø 8", hauteur 2"
    dans la référence de commande, remplacer le 0 par un 2, à la cinquième position par exemple 30.1820.03 par exemple 35.1820.03
    Tamis d'analyse à ouverture de mailles de 5 mm
    Ø 100 mm, hauteur 40 mm
    dans la référence de commande, remplacer le 0 par un 4, à la cinquième position par exemple 30.1840.03 par exemple 35.1840.03
  • Autres informations

    Des tamis d'analyse et accessoires de tamisage d'autres diamètres et ouvertures de maille sont disponibles sur demande.
    Des tamis d'analyse en polyamide sont disponibles sur demande.
    Aucun tamis d'analyse et accessoires de tamis ne peut être échangé.

Pour le tamisage à sec et par voie humide, ouverture de maille comprise entre 20 μm et 63 mm : particulièrement léger et robuste, fabrication haut de gamme. L'acier inoxydable fortement allié protège de la corrosion et facilite le nettoyage. Les jonctions sans rainure de la toile empêchent la souillure du produit à tamiser. Tous les tamis sont gravés au laser, mesurés avec un système optique et fournis avec un certificat d'usine.

Choisissez les tamis d'analyse

Tamis d'analyse en acier inoxydable, 8" intérieur, 2" de hauteur selon ASTM E11, avec certificat d'usine

1" = 25 mm mesh width
N° 35.0220.03
Test sieve, mesh width ASTM 1" = 25 mm

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
7/8" = 22.4 mm mesh width
N° 35.0320.03
Test sieve, mesh width ASTM 7/8" = 22.4 mm

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.

In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
3/4" = 19 mm mesh width
N° 35.0620.03
Test sieve, mesh width ASTM 3/4" = 19 mm

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
5/8" = 16 mm mesh width
N° 35.0820.03
Test sieve, mesh width ASTM 5/8" = 16 mm

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
0.53" = 13.2 mm mesh width
N° 35.0920.03
Test sieve, mesh width ASTM 0.53" = 13.2 mm

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
1/2" = 12.5 mm mesh width
N° 35.1020.03
Test sieve, mesh width ASTM 1/2" = 12.5 mm

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
7/16" = 11.2 mm mesh width
N° 35.1120.03
Test sieve, mesh width ASTM 7/16" = 11.2 mm

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
3/8" = 9.5 mm mesh width
N° 35.1220.03
Test sieve, mesh width ASTM 3/8" = 9.5 mm

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
5/16" = 8 mm mesh width
N° 35.1420.03
Test sieve, mesh width ASTM 5/16" = 8 mm

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
0.265" = 6.7 mm mesh width
N° 35.1520.03
Test sieve, mesh width ASTM 0.265" = 6.7 mm

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
1/4" = 6.3 mm mesh width
N° 35.1620.03
Test sieve, mesh width ASTM 1/4" = 6.3 mm

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
3 1/2 = 5.6 mm mesh width
N° 35.1720.03
Test sieve, mesh width ASTM 3 1/2 = 5.6 mm

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
4 = 4.75 mm mesh width
N° 35.1820.03
Test sieve, mesh width ASTM 4 = 4.75 mm

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
5 = 4 mm mesh width
N° 35.2020.03
Test sieve, mesh width ASTM 5 = 4 mm

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
6 = 3.35 mm mesh width
N° 35.2120.03
Test sieve, mesh width ASTM 6 = 3.35 mm

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
7 = 2.8 mm mesh width
N° 35.2320.03
Test sieve, mesh width ASTM 7 = 2.8 mm

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
8 = 2.36 mm mesh width
N° 35.2420.03
Test sieve, mesh width ASTM 8 = 2.36 mm

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
10 = 2 mm mesh width
N° 35.2620.03
Test sieve, mesh width ASTM 10 = 2 mm

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
12 = 1.7 mm mesh width
N° 35.2820.03
Test sieve, mesh width ASTM 12 = 1.7 mm

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
14 = 1.4 mm mesh width
N° 35.2920.03
Test sieve, mesh width ASTM 14 = 1.4 mm

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
16 = 1.18 mm mesh width
N° 35.3020.03
Test sieve, mesh width ASTM 16 = 1.18 mm

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
18 = 1 mm mesh width
N° 35.3220.03
Test sieve, mesh width ASTM 18 = 1 mm

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
20 = 850 µm mesh width
N° 35.3420.03
Test sieve, mesh width ASTM 20 = 850 <span class="to-lower">µm</span>

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
25 = 710 µm mesh width
N° 35.3520.03
Test sieve, mesh width ASTM 25 = 710 <span class="to-lower">µm</span>

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
30 = 600 µm mesh width
N° 35.3620.03
Test sieve, mesh width ASTM 30 = 600 <span class="to-lower">µm</span>

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
35 = 500 µm mesh width
N° 35.3820.03
Test sieve, mesh width ASTM 35 = 500 <span class="to-lower">µm</span>

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
40 = 425 µm mesh width
N° 35.4020.03
Test sieve, mesh width ASTM 40 = 425 <span class="to-lower">µm</span>

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
45 = 355 µm mesh width
N° 35.4120.03
Test sieve, mesh width ASTM 45 = 355 <span class="to-lower">µm</span>

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
50 = 300 µm mesh width
N° 35.4220.03
Test sieve, mesh width ASTM 50 = 300 <span class="to-lower">µm</span>

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
60 = 250 µm mesh width
N° 35.4420.03
Test sieve, mesh width ASTM 60 = 250 <span class="to-lower">µm</span>

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
70 = 212 µm mesh width
N° 35.4620.03
Test sieve, mesh width ASTM 70 = 212 <span class="to-lower">µm</span>

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
80 = 180 µm mesh width
N° 35.4720.03
Test sieve, mesh width ASTM 80 = 180 <span class="to-lower">µm</span>

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
100 = 150 µm mesh width
N° 35.4820.03
Test sieve, mesh width ASTM 100 = 150 <span class="to-lower">µm</span>

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
120 = 125 µm mesh width
N° 35.5020.03
Test sieve, mesh width ASTM 120 = 125 <span class="to-lower">µm</span>

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
140 = 106 µm mesh width
N° 35.5220.03
Test sieve, mesh width ASTM 140 = 106 <span class="to-lower">µm</span>

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
170 = 90 µm mesh width
N° 35.5420.03
Test sieve, mesh width ASTM 170 = 90 <span class="to-lower">µm</span>

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
200 = 75 µm mesh width
N° 35.5820.03
Test sieve, mesh width ASTM 200 = 75 <span class="to-lower">µm</span>

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
230 = 63 µm mesh width
N° 35.6020.03
Test sieve, mesh width ASTM 230 = 63 <span class="to-lower">µm</span>

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
270 = 53 µm mesh width
N° 35.6220.03
Test sieve, mesh width ASTM 270 = 53 <span class="to-lower">µm</span>

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
325 = 45 µm mesh width
N° 35.6620.03
Test sieve, mesh width ASTM 325 = 45 <span class="to-lower">µm</span>

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
400 = 38 µm mesh width
N° 35.7020.03
Test sieve, mesh width ASTM 400 = 38 <span class="to-lower">µm</span>

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
450 = 32 µm mesh width
N° 35.7220.03
Test sieve, mesh width ASTM 450 = 32 <span class="to-lower">µm</span>

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
500 = 25 µm mesh width
N° 35.7620.03
Test sieve, mesh width ASTM 500 = 25 <span class="to-lower">µm</span>

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
635 = 20 µm mesh width
N° 35.7820.03
Test sieve, mesh width ASTM 635 = 20 <span class="to-lower">µm</span>

Test sieve 8" dia., 2" height, frame and mesh wire made of stainless steel with compliance certificate.


In the selection aid you will find the order numbers for this sieve in the following sizes:
200 mm dia., 25 mm height
200 mm dia., 50 mm height
100 mm dia., 40 mm height


ANALYSE DE RÉFÉRENCE
General specifications
MaterialStainless steel – 1.4301
ISO/EN/DIN codeX5CrNi18-10
Chemical composition
ElementShare %
Iron – Fe66.75
Carbon – C0.070
Silicon – Si1.000
Manganese – Mn2.000
Phosphorus – P0.045
Sulphur – S0.030
Chromium – Cr19.5
Nickel – Ni10.5
Nitrogen – N0.110
Physical and mechanical properties
Density7.9 g/cm³
Hardness215 HB


Explanations on hardness data
Référence
03.8020.00
Jessica Seifert
FRITSCH GmbH - Milling and Sizing
Industriestrasse 8
55743 Idar-Oberstein
Téléphone +49 67 84 70 0
EFFECTUEZ UN TEST

ANALYSE PAR TAMISAGE GRATUITE

Faites-nous parvenir un échantillon, nous le soumettrons à une analyse par tamisage - nous vous enverrons un compte rendu individuel de tamisage.